Using Surplus Tubes

home home home

THE PROBLEM:
After I had obtained a few surplus Russian tubes from Dr Alex, UR4LL he sent me an e-mail entitled "Starting Procedure". The subject of this message certainly piqued my curiosity! As I read it, I realized I had forgotten a very important aspect of using tubes which have spent a significant amount of time, often years, "on the shelf" awaiting use! Due to the nature of physical materials, a certain amount of gases are always trapped inside the metals and ceramics, etc., used to construct each tube. A vacuum tube depends on a relatively hard vacuum to function without arcs and other undesired, often disasterously destructive, internal current flow. While in storage, a certain amount of the gases trapped in its materials is "leached" out into the vacuum of the tube. If one were to plug such a tube into an amplifier and apply all voltages and drive, the small amount of gas within the tube would ionize and provide said undesired internal conductive paths; such conduction often reduces an otherwise useful tube to trash. It is, however, possible to prevent these events from occurring by taking some rather simple measures to prepare such tubes for use!

THE SOLUTION:
Fortunately, tube manufacturers considered this situation, and inside each vacuum tube is a metal surface called a "getter" - a surface made from some particularly reactive metal like barium. Being very reactive, it will react with more or less any molecule that hits its surface, and form a non-volatile reaction product. In a small glass tube, the getter is the shiny surface on the inside of the glass wall. The trick is to get the atoms of gas to move around enough to strike the getter and become absorbed. This is what UR4LL's e-mail addressed. I also did some reading on the internet and found an applicable Technical Bulletin from Svetlana and a very nice treatise by SM5BSZ, including input from SM6EHY, which put it all in perspective. I include three excerpts from SM5BSZ:

"As amateurs, we often use old tubes. They may be unused, but may have spent a very long time stored away. A high power tube should work at very high voltages without arcing so it has to have a very good vacuum. When the tube is stored, vacuum gradually deteriorates over time and the procedures below will help to restore a good vacuum.

The cathode is the "heart" of the tube. There are several types of cathodes, and they have different properties. Read in the manufacturers data book how to treat the cathode of the tube you are going to use. A pure tungsten cathode will give maximum tube life if the heater voltage is made as low as possible for the desired output power, while a thoriated tungsten cathode may be damaged if it is underheated.

When the heater is switched on for the first time, it may be important to allow it to reach its final temperature slowly. I have been told that a slow heating, raising the voltage from zero to nominal gradually, over a time of several hours, will increase tube life considerably in normal professional operation. I guess this has something to do with a rechrystalisation that takes place when the heater wire is heated for the first time, but I do not really know."


PREPARING SURPLUS TUBES FOR USE
 

From UR4LL:
    1. Only Ufil during 12 hours min.
    2. To ground all grids.
    3. 25% of Ua during 4 hours.
    4. 50% of Ua during 4 hours.
    5. 100% of Ua during 4 hours.

COMMENTS: We have found that some of the larger tubes do a lot better if we bring filament voltage up, either over a period of a minute or so using a variac, or using the procedure in "Step 1", below, and leave the power on in this manner (with cooling fan on or liquid coolant flowing) for three to five days. We have found, for example, that GS-23B operation can be SIGNIFICANTLY enhanced, especially for those which work at 23cM, by a minimum of five (5) days with the filament on as described!

Subject to adjustments as outlined above, the steps shown below (prepared 16 June 2000) will change as further experience dictates:

Step 1:  Per SM5BSZ, I'm going to bring the filament voltage (Ufil) up slowly; probably 20% Ufil for the 1st hour, 40% during the 2nd hour, 60% in the 3rd hour, 80% for the 4th hour and, finally, apply 100% Ufil after four hours, leaving it applied until 12 hours has elapsed. I will turn the forced air cooling on at the start of the second hour.

Steps 2 & 3:  I have a variac on the input to my HV supply and will vary the plate voltage (Ua, or anode voltage) as required to obtain the specified percentage for the specified period. If you don't have a means to vary your HV, SM6EHY says, "Connect the anode through a 50 to 100 kiloohm resistor. Leave the tube with the plate voltage through this resistor for 2 hours. If the tube has been unused several years, leave it for 24 hours." Most of my tubes are from surplus "spares stock" and are several years old. Based on this, I will have to err on the side of too much time at each level, rather than trying to shorten the process in any way! UR4LL says to ground all grids before applying Ua; SM6EHY says nothing about the grids until his equivalent of step 4.

Step 4:  Again, I will vary my HV using the power supply variac. SM6EHY suggests, "Now the vacuum is improved, and you can replace the 50 to 100 k ohm resistor by 1 k ohm and apply the screen grid voltage. Start with a reduced screen grid voltage for half an hour and then apply full voltage and wait for half an hour again. In both cases, the control grid voltage should be adjusted for negligible plate current." If I see plate current starting to creep up, I will unground the control grid and apply bias per SM6EHY.

Step 5:  I will follow UR4LL's procedure. After step five, he says, "Tube is ready for use." Step five per SM5EHY: "Now it is time to remove the plate resistor and start to use the tube with some RF." Click here To read SM5EHY's comments within the context of the SM5BSZ web page.

Comments and feedback are welcome! Please e-mail me through the "Feedback" link, below!


go to the top of the page  


Best Viewed: MSIE 4.0 & higher, or Netscape 3.02 & higher, and screen set to 800x600 pixels
This Page Last Updated: 25 April 2004
Feedback: Paul S. Goble, III, ND2X
Copyright © 1998 - 2004 by ND2X, all rights reserved